2018-2019 Undergraduate Academic Catalog

EGME-2510 Statics –Fa 3 hours Introduction to analyzing forces in isolated and connected rigid- body systems; vector analysis, forces, moments, resultants, two- and three-dimensional equilibrium, centroids, moment of inertia, friction, trusses, frames, and machines. Design project required. Prerequisites: EGME-1810 Engineering Graphics; PHYS-2110 General Physics I; MATH-1720 Analytical Geometry and Calculus II. (Fee: $10) EGME-2530 Statics and Mechanics of Materials –Fa 5 hours Introduction to analyzing forces in isolated and connected rigid- body systems; vector analysis, forces, moments, resultants, two- and three-dimensional equilibrium, centroids, distributed loading, moment of inertia, friction, trusses, frames, and machines. Introduction to the theoretical and experimental analysis of deformable bodies subject to applied loads; normal and shear stress and strain, strain energy, torsion, stresses in beams, deflection of beams, combined stress, stress transformation, failure theories, and buckling of columns. Design project required. Prerequisites: EGME-1810 Engineering Graphics; PHYS-2110 General Physics I; MATH-1720 Calculus II. (Fee: $25) EGME-2570 Statics and Dynamics –Fa 3 hours Free-body diagrams, vectors, resultant forces, two- and three- force members, friction, simple machines, center of gravity, and moments of inertia. Kinematics and equations of motion of a particle for rectilinear and cervilinear motion. Planar kinematics of rigid bodies. Kinetics for planar motion of rigid bodies, including equations of motion and principles of energy and momentum. Prerequisites: EGME-1810 Engineering Graphics; MATH-1720 Calculus II; PHYS-2110 General Physics I. (Fee: $10) EGME-2630 Dynamics –Sp 3 hours Introduction to kinematic and kinetic analysis of particles, systems of particles, and rigid bodies; position, velocity, acceleration, non-rotating and rotating frames of reference, Newton’s laws, work, energy, impulse, momentum, conservative and non-conservative systems, and vibration of single-degree-of- freedom systems. Design project required. Prerequisite: EGME- 2510 Statics or EGME-2530 Statics and Mechanics of Materials. Pre- or Corequisite: MATH-2740 Differential Equations. (Fee: $10) EGME-3010 2 hours Mechanical Engineering Laboratory I –Fa Experiments using the wind tunnel, engine test cell, testing machines in the mechanics laboratory, vibrations laboratory, fluids laboratory, refrigeration laboratory, and heat transfer laboratory are conducted. Students measure mechanical phenomena such as acceleration, force, pressure, temperature, strain, fluid flow, viscosity, and heat transfer using transducers, instrumentation, and PC-based data acquisition. Students design some of the experiments. Two 2-hour laboratories per week. Prerequisites: EGME-2630 Dynamics; EGEE-2050 Circuits and Instrumentation. Corequisites: EGME-3110 Thermodynamics; EGME-3210 Fluid Mechanics. (Fee: $100) EGME-3020 2 hours Mechanical Engineering Laboratory II –Sp Continuation of EGME-3010. Two two-hour laboratories per week. Prerequisite: EGME-3010 Mechanical Engineering Laboratory I. Corequisite: EGME-3150 Heat Transfer. (Fee: $100) EGME-3050 3 hours Introduction to Finite Element Analysis –Sp Introduction to basic components of the finite element method including element selection, shape functions, strain-displacement and stress-strain relations, formulation of the stiffness matrix for 1-D, 2-D, and 3-D elements, linear strain and isoparametric formulations, application of boundary conditions, and interpretation of results; application to 2-D and 3-D problems and experience using a commercial code. Prerequisites: EGME-2050 Computational Methods; EGME-2530 Statics and Mechanics of Materials. (Fee: $25) EGME-3110 Thermodynamics –Fa 5 hours Introduction to engineering thermodynamics, properties of pure substances, work, heat, first and second laws of thermodynamics, energy, enthalpy, and entropy. Specific application to power, refrigeration cycles, and combustion processes. Prerequisites: CHEM-1050 Chemistry for Engineers; MATH-2710 Calculus III. EGME-3130 Internal Combustion Engines –Sp 3 hours Introduction to internal combustion engines, fuel-air cycles, engine simulation, emissions, engine performance and alternative fuels. Prerequisites: EGME-2630 Dynamics; EGME-3110 Thermodynamics. EGME-3150 Heat Transfer –Sp 3 hours Introduction to conduction, convection, and radiation heat transfer in one and two dimensions; free and forced convection, analytical and computational techniques applied to Fourier’s Law of conduction, Newton’s Law of cooling, and Stefan-Boltzman’s Law of thermal radiation. A heat exchanger design project is required. Prerequisites: EGME-3110 Thermodynamics; EGME- 3210 Fluid Mechanics. Corequisite: EGME-2050 Computational Methods. EGME-3170 Thermal Systems –Sp 2 hours Introduction to engineering thermodynamics, properties of pure substances, work, heat, enthalpy, and first law of thermodynamics. Introduction to conduction and convection modes of heat transfer. Prerequisites: CHEM-1050 Chemistry for Engineers; MATH-2740 Differential Equations. EGME-3210 Fluid Mechanics –Fa 3 hours Introduction to fluid properties, fluid statics, and the concepts, definitions, and basic equations for subsonic fluid dynamics; Navier-Stokes equation, viscous and invisid fluid flows, potential flow analysis, boundary layers, laminar and turbulent flows, analytical and computational solutions, vector fields, and finite- integral-control-volume method. Prerequisites: MATH-2710 Calculus III; MATH-2740 Differential Equations. EGME-3430 Principles of Physical Metallurgy –Sp 3 hours Introduction to the physical and mechanical properties of metals and alloys; crystal structure, phase equilibria, defects, strengthening mechanisms, and kinetics of reactions. Prerequisite: EGME-2410 Properties of Engineering Materials. EGME-3450 Plastic and Composite Materials –Sp 2 hours Introduction to the properties and processing of plastics, resins, and adhesives; rheology, creep-deformation history, and injection molding. Fiber-reinforced, carbon-carbon, and metal-matrix composites are analyzed for strength, anisotropy, and applicability. Prerequisite: EGME-2410 Properties of Engineering Materials. EGME-3610 3 hours Kinematics and Design of Machines –Sp Introduction to the analysis and synthesis of motion in planar mechanisms and linkages; velocity and acceleration analysis, cam design, gears, simple and compound gear trains, computer solution and simulation. Design project required. Prerequisite: EGME-2630 Dynamics. (Fee: $40) EGME-3850 Mechanical Design –Sp 3 hours Further development of load determination, stress, strain, deflection and failure theories; integration of an iterative problem solver in the design process; and analysis of fatigue failure. Introduction to the design of mechanical components including shafts, keys, couplings, bearings, gears, springs, and fasteners. Prerequisite: EGME-2410 Properties of Engineering Materials. Corequisites: EGME-3020 Mechanical Engineering Laboratory II; EGME-3610 Kinematics and Design of Machines. (Fee: $25) 2017–18 Undergraduate Academic Catalog Page 257 Course Descriptions EGME-2510 – EGME-3850 ENGINEERING AND COMPUTER SCIENCE